Sharpening Part 27 – The Entire Face

A beautiful face: Oohirayama Lotus stone

If a dog will not come to you after having looked you in the face, you should go home and examine your conscience.

Woodrow Wilson

The subject of how to use the face of your sharpening stone is so basic and seems so unimportant that few give it the attention it warrants. But it is not trivial: it deserves its own post because it can truly make a big difference in the time and money you spend sharpening.

Money Down the Drain

Instead of focusing his attention on the blade alone, a wise man will make a conscious effort to use the entire face of his sharpening stone from edge to edge, end to end, and corner to corner instead of digging an oval swamp in the center of his stone’s face.

This habit will help to keep a stone’s faces flatter over more strokes longer, saving time truing the stone, and extending its life thereby saving money.

Remember that you paid money for the stone, the entire stone, not just the hollowed-out oval area in the center most people create when carelessly sharpening. How much of a stone do most people throw away? Idunno, 20%? If you paid $100 dollars for the stone, that means $20 was turned into mud and washed away without providing any benefit to you at all. And don’t forget that you had to spend time cutting down those high spots to keep the stone’s face flat. That makes it more than a $20 loss if you count your time worth anything, which you should.

Why not use the sides and ends of the stone too?

Developing Good Habits

When developing these intelligent work habits, use a carpenter’s pencil to cross-hatch the stone’s surface to help you keep track of the areas you have not yet touched. Industrial diamonds are made from graphite, it’s true, but pencil lead is still softer than the finest sharpening stone and won’t affect the sharpening process one way or another.

Also, before and while sharpening, frequently use a thin stainless steel ruler to check the stone’s face lengthwise and crosswise at various locations, and of course on the diagonals to monitor wear. Don’t guess, lazy bones, examine. Between ruler and pencil you may discover you have developed less-than-efficient sharpening habits. With some thought you will also figure out how to change those habits so your sharpening efforts will be quicker and more cost-effective.

Before long, you will be able to detect uneven wear and warpage fairly reliably without using either tool as much, so stick with it until you do.

Hang Ten

One conundrum you have probably already discovered is that it is impractical to use the extreme right and left sides and both ends of the stone’s face to sharpen a blade. Or is it? Here is wisdom: Teach yourself how to sharpen with one corner of the blade hanging off the stone part of the time, alternating between right and left corners, of course. Strange as it may seem this technique is effective at not only keeping your sharpening stone flatter, but for keeping the cutting edges of your blades straighter. If this doesn’t make sense to you, think about it real hard. Then give it a try and you will see what I mean.

And since you are taking short strokes anyway, why not work the blade crosswise at the ends of the stone? A lot of expensive stone going to waste there.

I hate to sound like a broken record, but you will find that making short strokes will make it much easier to use the entire face of the stone.

If you feel this post needlessly states the obvious, or is “verbose,” allow me to remind our Gentle Readers once again that the purpose of this blog is not to provide entertainment, sell stuff, troll for clicks or snag subscribers but to help our Beloved Customers develop good work habits through education. Some of them are newbies, and others are old hands, but if I were to write only for the professionals then I would be neglecting the newbies, so if you know this stuff already please congratulate yourself and celebrate your good fortune by buying a new carpenter’s pencil.

Related image

YMHOS

If you have questions or would like to learn more about our tools, please use the questions form located immediately below. Please share your insights and comments with everyone in the form located further below labeled “Leave a Reply.” We aren’t evil Google or incompetent facebook and so won’t sell, share, or profitably “misplace” your information.

Other Posts in the Sharpening Series

Sharpening Japanese Woodworking Tools Part 1

Sharpening Part 2 – The Journey

Sharpening Part 3 – Philosophy

Sharpening Part 4 – ‘Nando and the Sword Sharpener

Sharpening Part 5 – The Sharp Edge

Sharpening Part 6 – The Mystery of Steel

Sharpening Part 7 – The Alchemy of Hard Steel 鋼

Sharpening Part 8 – Soft Iron 地金

Sharpening Part 9 – Hard Steel & Soft Iron 鍛接

Sharpening Part 10 – The Ura 浦

Sharpening Part 11 – Supernatural Bevel Angles

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Sharpening Part 13 – Nitty Gritty

Sharpening Part 14 – Natural Sharpening Stones

Sharpening Part 15 – The Most Important Stone

Sharpening Part 16 – Pixie Dust

Sharpening Part 17 – Gear

Sharpening Part 18 – The Nagura Stone

Sharpening Part 19 – Maintaining Sharpening Stones

Sharpening Part 20 – Flattening and Polishing the Ura

Sharpening Part 21 – The Bulging Bevel

Sharpening Part 22 – The Double-bevel Blues

Sharpening Part 23 – Stance & Grip

Sharpening Part 24 – Sharpening Direction

Sharpening Part 25 – Short Strokes

Sharpening Part 26 – The Taming of the Skew

Sharpening Part 27 – The Entire Face

Sharpening Part 26 – The Taming of the Skew

My relationship to reality has been so utterly skewed for so long that I don’t even notice it any more. It’s just my reality.

Ethan Hawke

The Taming of the Skew

You will have noticed that it is easier to keep a blade stable when sharpening its bevel if you skew it on the stone. There is nothing wrong with skewing the blade so long as you understand the natural consequences of doing so and compensate for them appropriately.

Let’s examine some of those consequences.

First, a skewed blade tends to wear-out, or hollow-out, the center area of the stone quicker. This is inefficient, wasting time and stones, but can be compensated for if you pay attention and work the blade evenly over the stone’s entire face.

Second, people tend to place uneven pressure on a skewed blade, wearing the blade unevenly.

In addition, the leading corner is exposed to more fresher, larger grit particles (which cut more aggressively) than the trailing corner. As a result, the blade’s leading corner tends to be abraded more, causing the blade’s edge to gradually become skewed or rounded in shape over many sharpening sessions. This is definitely bad, and is often mistaken for the work of those devilish iron pixies. But if you are aware this can happen, and pay attention, you can compensate for it. 

Third, and I have no way to confirm this, I am told by the guys with microscopes that diagonal scratches at the extreme cutting edge leave it a tad weaker, causing it to dull just a bit quicker. The way to compensate for this is to keep the blade’s cutting edge perpendicular to the direction of travel during the last few strokes on the finishing stone.

So in summary, habitually skewing a blade while sharpening is fine, but may cost a little efficiency, and may cause your blades and stones to become distorted.

Please read the quotation at the top of this article and consider whether or not your sharpening reality has become skewed without your realizing it. I know mine was for a long time.

These aren’t things you wouldn’t have figured out for yourself eventually, Beloved Customers and Gentle Readers, but now, at least if you pay attention, you’re a few years ahead on the learning curve.

In the worst case, at least ignorance isn’t an excuse anymore.

YMHOS

Related image
Shakespeare’s Shrew, Katherine Minola, played by Elizabeth Taylor in the 1987 movie. In this photograph she’s obviously watching someone skewing a plane or chisel blade while sharpening it. She has the classic “squint eye” down perfectly, as did Clint Eastwood, of course.

If you have questions or would like to learn more about our tools, please use the questions form located immediately below. Please share your insights and comments with everyone in the form located further below labeled “Leave a Reply.” We aren’t evil Google or incompetent facebook and so won’t sell, share, or conveniently and profitably “misplace” your information.

Other Posts in the Sharpening Series

Sharpening Japanese Woodworking Tools Part 1

Sharpening Part 2 – The Journey

Sharpening Part 3 – Philosophy

Sharpening Part 4 – ‘Nando and the Sword Sharpener

Sharpening Part 5 – The Sharp Edge

Sharpening Part 6 – The Mystery of Steel

Sharpening Part 7 – The Alchemy of Hard Steel 鋼

Sharpening Part 8 – Soft Iron 地金

Sharpening Part 9 – Hard Steel & Soft Iron 鍛接

Sharpening Part 10 – The Ura 浦

Sharpening Part 11 – Supernatural Bevel Angles

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Sharpening Part 13 – Nitty Gritty

Sharpening Part 14 – Natural Sharpening Stones

Sharpening Part 15 – The Most Important Stone

Sharpening Part 16 – Pixie Dust

Sharpening Part 17 – Gear

Sharpening Part 18 – The Nagura Stone

Sharpening Part 19 – Maintaining Sharpening Stones

Sharpening Part 20 – Flattening and Polishing the Ura

Sharpening Part 21 – The Bulging Bevel

Sharpening Part 22 – The Double-bevel Blues

Sharpening Part 23 – Stance & Grip

Sharpening Part 24 – Sharpening Direction

Sharpening Part 25 – Short Strokes

Sharpening Part 26 – The Taming of the Skew

Sharpening Part 27 – The Entire Face

Sharpening Part 24 – Sharpening Direction

Related image

If you do not change direction, you may end up where you are heading.

Lao Tzu

When using the rough stones, and especially when learning basic sharpening skills, it is best to sharpen the bevel in one direction only, lifting the blade off the stone, or at least removing all downward pressure, on the return stroke. The reason for this seemingly inefficient movement is simply that, at least for most people, trying to abrade the blade on both push and pull strokes is extremely likely to cause the blade to rock creating the dreaded bulging bevel.

There are certainly many exceptions to this rule, and we actively encourage you to try to develop the concentration and muscle control required to sharpen in both directions on rough and medium stones, but be aware it may take some years. In the meantime, remember the ancient adage and imperial moto: festina lente, which we chose to translate as “Slow is smooth; Smooth is fast. “

Part of the difficulty of sharpening in both directions is the resulting loss of concentration: the swing of the thing is hard to sense. Perhaps another part of it is due to the difficulty of controlling the complicated and constantly-changing angles of bone and tendon. Both of these natural mental and physical tendencies can be overcome by talented and determined people given time and daily practice, but in the case of everyone I have ever talked with on the subject, it takes many years of focused on-the-job practice, and extreme concentration at first to overcome pre-existing bad habits and avoid developing bad muscle memory.

Which Direction?

At this point you need to make a decision, unless you have already made it inadvertently. That is, to sharpen on either the push stroke (pushing the blade away from you) or the pull stroke (pulling the blade towards you). Most people choose the push stroke, as do I, but in reality the pull stroke is actually a little more efficient because the pressure tends to focus closer to the bevel’s front instead of back, and rocking is reduced. Whichever direction you choose, use it consistently.

However, and this is critically important, when it comes to the final finishing stone, work the blade back and forth in both directions. The finishing stone is not abrasive enough to change the bevel’s shape, and since you need to polish the last few microns width of blade’s cutting edge, a very tiny amount of unintentional rocking is actually helpful, as mentioned in a previous post.

Training Techniques

If you decide you want to develop the ability to sharpen on both push and pull strokes, I can share some helpful guidance that was given to me many years ago by a sword polisher.

The first step in training yourself is to begin by lifting the blade on the return stroke (either push or pull depending on your preferred direction). All the things mentioned above apply. Becoming proficient with this technique is foundational. Strive to project your senses into the blade traveling over the stone, indeed right down to the last few microns of the cutting edge.

When you are able to create a sharp edge while maintaining a flat bevel consistently and without much concentration using this “one-way” technique, then move on to the second step, which is to keep the blade in contact with the stone on the return stroke, but relieve all downward pressure. Begin slowly with full concentration and and seek for smooth motion. It’s at the transition from one direction to the other where those nasty iron pixies cast their spells of confusion.

And finally, when you have mastered the “light-touch” technique, try applying downward pressure in both directions, beginning slowly at first and with full concentration striving for smooth motion.

Remember, don’t grip the blade like a thrashing snapping turtle, but hold it lightly in your hands like a small bird: too tightly and it will be crushed; too loosely and it will fly away. Don’t lock your wrists or elbows, but actively and consciously rotate them to keep the blade’s bevel always perfectly flat on the stone (your stone is flat right, right?). And don’t forget to use your small, thin stainless steel straightedge and brass bevel gauge to frequently check the bevel for flatness and proper angle.

And as always, brutally crush bad habits, and don’t allow new bad ones to take root.

Sadly, this is a skill that, once learned, tends to deteriorate with time unless practiced frequently. As with cherry blossoms, muscles, tendons and eyes are neither static nor eternal. Setsunai, desu ne.

YMHOS

If you have questions or would like to learn more about our tools, please use the questions form located immediately below. Please share your insights and comments with everyone in the form located further below labeled “Leave a Reply.” We aren’t evil Google or incompetent facebook and so won’t sell, share, or conveniently and profitably “misplace” your information.

Other Posts in the Sharpening Series

Sharpening Japanese Woodworking Tools Part 1

Sharpening Part 2 – The Journey

Sharpening Part 3 – Philosophy

Sharpening Part 4 – ‘Nando and the Sword Sharpener

Sharpening Part 5 – The Sharp Edge

Sharpening Part 6 – The Mystery of Steel

Sharpening Part 7 – The Alchemy of Hard Steel 鋼

Sharpening Part 8 – Soft Iron 地金

Sharpening Part 9 – Hard Steel & Soft Iron 鍛接

Sharpening Part 10 – The Ura 浦

Sharpening Part 11 – Supernatural Bevel Angles

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Sharpening Part 13 – Nitty Gritty

Sharpening Part 14 – Natural Sharpening Stones

Sharpening Part 15 – The Most Important Stone

Sharpening Part 16 – Pixie Dust

Sharpening Part 17 – Gear

Sharpening Part 18 – The Nagura Stone

Sharpening Part 19 – Maintaining Sharpening Stones

Sharpening Part 20 – Flattening and Polishing the Ura

Sharpening Part 21 – The Bulging Bevel

Sharpening Part 22 – The Double-bevel Blues

Sharpening Part 23 – Stance & Grip

Sharpening Part 24 – Sharpening Direction

Sharpening Part 25 – Short Strokes

Sharpening Part 26 – The Taming of the Skew

Sharpening Part 27 – The Entire Face

Sharpening Part 23 – Stance & Grip

When the show starts, I am in my SpongeBob stance, and I walk like SpongeBob, and the first step that I take, I am SpongeBob.

Ethan Slater
Ok boiz and gurlz, ready to sharpen?!

Stances

There are several practical stances for sharpening, including standing, sitting on a bench or in a chair, squatting, kneeling on the floor, or sitting on the floor. With practice, all these stances can be made to work well.

When starting out, however, I think most people benefit from using a standing position with the stones placed on a workbench or table, or on a board spanning a sink. 

Whichever stance you choose, locate and be conscious of your center of gravity, (usually just below your belly button), and try to keep it at the same elevation while moving the blade forward and back. 

Flex your knee joints, and loosen your elbow joints and wrists. Locking up your wrists and elbows will make it impossible to avoid rocking the blade. This is important. Actively concentrate on allowing the wrist to rotate in a manner to keep the blade’s bevel flat on the stone’s face.

In the case of a normal resharpening job, instead of a major repair, remember the goal: to abrade and polish the last few microns of steel at the extreme cutting edge, using the flat bevel as an alignment jig, exactly as craftsmen have been doing for thousands of years.

Don’t let yourself get lost in the forest of trees and focus just on abrading and polishing the entire bevel. Focus the majority of pressure on the extreme cutting edge, and less on the rear of the bevel, but without lifting the rear of the bevel off the stone. In the case of Japanese blades, the rear of the bevel is all soft jigane iron and will take care of itself. Yes, it is a balancing act. Yes, it takes focus. Yes, you will make mistakes, overbalance, gouge the stone and mess up the cutting edge a time or two. Everyone since the day the first caveman tried to grind his stone axe on another stone has made that mistake, so don’t worry about it. You fell off your bicycle the first few tries, scraped your knees and elbows, survived, and now ride like the wind! Yiiiiiihah!

Get a Grip

The way you hold your plane or chisel blade during sharpening will greatly influence the quality of the end product and the stress placed on your hands during the process, so it is worth paying attention to.

There are as many was to hold a plane or chisel blade when sharpening as Baskin Robbins has ice cream flavors. And like ice cream, none are right or wrong, except Burgundy Cherry, which of course is superior to all others (ツ)。 In the interest of brevity, we will only look at three grip methods. If you are not using them now, I suggest you give each a try over a couple of sharpening sessions to see if they are an improvement or not. Feel free to adapt these or develop your own from scratch once you understand the key points.

The Gorilla Grip

First, let’s examine what I call the “Gorilla Grip.” With the plane blade resting ura facing up, the blade’s long axis pointing at 11:00, and the cutting edge furthest away from you, grip the blade’s sides with your right-hand’s thumb on the left side, ring finger and pinkie on the right, the tip of the middle finger resting on the right corner directly behind the cutting edge, and index finger extended alongside the middle finger. Then lift the blade and roll your ring and pinkie under it.

Rest the tip of the ring finger of your left hand on the left corner directly behind the cutting edge, with your middle finger and index fingers extended and their tips resting adjacent.

Extend your left palm over your right thumb’s last joint, and wrap your left thumb under the blade. You are now ready to rock-n-roll, without the rocking and rolling motion

The advantage to this grip is that it is very strong, ergo “ gorilla.” The downside is the blade tends to end up skewed on the stone because the right wrist must be twisted to keep the blade straight. Also, because the wrist joints are at very different angles with respect to the blade, and it is easy to apply a lot of force, extra care is necessary to keep the wrists firm but loose and rotating in harmony.

Notice how thumbs are poised to fit under the blade’s head
Four fingers pressing down on the blade’s ura as close to the cutting edge as reasonably possible.
Finger position on a chisel. The left hand thumb passes under the blade’s neck supporting it vertically, while the pad presses against the neck’s right side. The right hand thumb passes over the top of the neck, restraining the tool vertically, and presses against the neck’s left side firmly securing the neck between both thumbs. More fingers can press down on the ura in the case of wider blades. Conversely, only one finger can press on narrow blades.

The Three-finger Grip

The other grip is one I call “three-finger,”(指三本) after the most proper way of bowing in Japan when seated directly on the floor (preferably tatami mat) in the “seiza” posture with legs folded underneath the body, both hands touching side by side with the pads of three fingers of each hand extended and touching the floor in front of the knees, and the thumbs and pinkies tucked out of sight. Very proper, and elegant especially for ladies.

In the case of the three-fingers grip, the blade is oriented directly in front of and on the body’s centerline with cutting edge furthest away. The hands hold the blade in a more symmetrical fashion than the gorilla grip, with the middle and index fingers pressing down on the blade’s corners closest the cutting edge (depending on the space available), with the thumbs curled under the blade’s head (end opposite the cutting edge), and either the ring fingers or pinkies touching the blade’s sides to assist in lifting it.

The advantages to this grip are less tendency to skew the blade, looser wrists, and better control of bevel angle. The disadvantage is slightly less power because it is harder to get the shoulders over the blade. This is the burgundy cherry version, in your humble servant’s opinion.

The Three-finger Monkey Grip

A hybrid of these two methods is one I call the “three-fingered monkey.” Place the right-hand thumb alongside the blade’s left side, instead of under the head forming a combination of the gorilla grip and three-finger grip. This method provides a little more power than the three-finger grip, and less skew than the gorilla grip.

Is one of these grips best? It’s like riding a bike: None are wrong, but some work better than others.

 In all three of these grips, most of the pressure will tend to focus at the blade’s corners which can create uneven wear on the ura. While this may be unavoidable, especially in the case of narrow blades, try to focus the majority of pressure on the centerline of the cutting edge. It seems insignificant, but if left uncorrected, the resulting unbalanced pressure will cause the blade to wear quicker at the corners and become curved. Yes the blade is iron and steel and does not flex much, but it is a verifiable fact that the points where your fingers apply pressure will be abraded quicker.

There is a saying in Japan which is quite appropriate when talking about sharpening that says “Dripping water wears away stone.” In this case, just a little differential pressure from your fingertips will shape the blade over many weeks and many passes over the stone, wearing away both stone and steel in useful ways or not. It is worth being aware of this potential and paying attention.

Chisel Grip

The grip I use on chisels is very similar to the grip for planes, and varies with width. 

The long handle makes chisels tail heavy and a bit more difficult to manage so it is often useful to select a grip style that is absolutely stable using just a single hand.

Most solutions involve holding the chisel in the palm secured by middle finger, ring finger, and pinkie, with the index finger extended and centered right behind the cutting edge.

The index and middle fingers of the other hand can also be pressed near the edge and the thumb wrapped underneath the handle.

Polishing the Ura

Polishing a 70mm plane blade’s ura.

When polishing the ura of a blade, be it plane or chisel, make sure the stone is flat. If it isn’t, you will regret it later without realizing why.

Let’s look at a plane blade first. Notice in the photo above how my right hand is curled under the blade’s head supporting it while my thumb presses down on the bevel close to the cutting edge, a grip that makes it easy to apply a lot of pressure precisely while maintaining control of the blade.

Two fingertips of my left hand are pressing down on the bevel for a total of three pressure points. The thumb can press down as light or hard as you feel is necessary, but it typically applies the highest amount of pressure. It’s important the left hand fingertips apply equal downward pressure to avoid creating uneven wear (unless one corner of the blade specifically needs more pressure applied).

Try to remove nearly all the weight of the blade’s head from the stone so that all but a tiny amount of applied pressure is focused on the “itoura” cutting land at the blade’s extreme cutting edge. No good can come of wearing a trench into the ura’s side lands.

Move the blade in two directions at the same time: Mostly to and fro in line with the cutting edge; but also on and off the stone’s edge perpendicular to the cutting edge. This will help avoid wearing a trench in the side lands and produce a stronger cutting edge (IMO).

Keep the stone flat and reverse it frequently to ensure even wear and less wasted stone.

Concentrate your senses and develop hand-soul coordination : You are a leaf on the wind; Watch how you soar (Hoban “Wash” Washburne in Serenity). I hope you have better luck than Wash did…

In the case of chisels, I hold the handle in the palm of my right hand and place thumb and forefinger on opposite sides of the neck/shoulders pinching it between them. I place the tips of the fingers of my left hand on the bevel, and move right and left hand together. And as in the case of plane blades, I move the blade both forward and backwards and left to right at the same time.

Give it a try. What do you have to loose?

In the next post in this series on sharpening, we will look at which direction to sharpen in. Few give this matter any thought, but most should.

YMHOS

If you have questions or would like to learn more about our tools, please use the questions form located immediately below. Please share your insights and comments with everyone in the form located further below labeled “Leave a Reply.” We aren’t evil Google or incompetent facebook and so won’t sell, share, or conveniently and profitably “misplace” your information.

Previous Posts in the Sharpening Series

Sharpening Japanese Woodworking Tools Part 1

Sharpening Part 2 – The Journey

Sharpening Part 3 – Philosophy

Sharpening Part 4 – ‘Nando and the Sword Sharpener

Sharpening Part 5 – The Sharp Edge

Sharpening Part 6 – The Mystery of Steel

Sharpening Part 7 – The Alchemy of Hard Steel 鋼

Sharpening Part 8 – Soft Iron 地金

Sharpening Part 9 – Hard Steel & Soft Iron 鍛接

Sharpening Part 10 – The Ura 浦

Sharpening Part 11 – Supernatural Bevel Angles

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Sharpening Part 13 – Nitty Gritty

Sharpening Part 14 – Natural Sharpening Stones

Sharpening Part 15 – The Most Important Stone

Sharpening Part 16 – Pixie Dust

Sharpening Part 17 – Gear

Sharpening Part 18 – The Nagura Stone

Sharpening Part 19 – Maintaining Sharpening Stones

Sharpening Part 20 – Flattening and Polishing the Ura

Sharpening Part 21 – The Bulging Bevel

Sharpening Part 22 – The Double-bevel Blues

Sharpening Part 23 – Stance & Grip

Sharpening Part 24 – Sharpening Direction

Sharpening Part 25 – Short Strokes

Sharpening Part 26 – The Taming of the Skew

Sharpening Part 27 – The Entire Face

Sharpening Part 22 – The Double-Bevel Blues

The fool doth think he is wise, but the wise man knows himself to be a fool.

William Shakespeare, As You Like It
It is well with me only when I have a chisel in my hand – Michelangelo Buonarroti 1475-1564

In the previous post in this series on sharpening Japanese tools, we looked at philosophical points such as making tools a long-term investment, as well as the upsides, downsides and causes of the bulging bevel. In this post, I would like to touch on a subject that will make thoughtful people think and befuddled folks lucid: The Double Bevel.

The Double-Bevel

Some people advocate creating double-bevels (primary and secondary) bevels, or what is sometimes called “micro-bevels” on plane and chisel blades. Multiple bevels have three useful applications in my opinion:

  1. The first useful application is to repair a tool’s blade in the field when there is not enough time to do a proper sharpening job. If a blade dulls or chips in the course of a job, we can quickly add a secondary bevel at a steeper angle to the blade’s primary bevel in a few seconds and get right back to work, but there will be a price to pay later over many sharpening sessions to restore the proper bevel, so it is only a temporary, not a long-term solution;
  2. The second application is to quickly adjust a plane blade’s angle to reduce tearout immediately when proper sharpening is not possible. Once again, a lot of remedial sharpening becomes necessary afterwards. This application is usually restricted to the primary bevel, but we will look at a more esoteric and risky application below.
  3. The third application is to efficiently restore a blade’s bevel to the correct angle in the case where pixies or our inattention has made the blade angle too shallow.

Case 3 above often goes like this: A blade that cuts well suddenly starts dulling quickly, maybe even chipping. Whiskey tango foxtrot!?! When this happens, our Beloved Customers, being of exceptionally high intelligence, use the bevel angle gauge described in Part 11 of this series to check the bevel angle. They may discover the bevel angle has become too shallow for the wood it is being asked to cut.

Image result for lie-nielsen honing jig photo

We could increase the bevel angle by welding metal to the bevel and regrinding it, but such barbaric behavior would ruin the blade, so the most expedient way to correct the bevel is to add a steeper secondary bevel at the desired angle. We can grind this new bevel by hand, or use a honing jig like the Lie-Nielson widget. I find I can apply more downward pressure using this jig to get the job done sooner and more precisely.

Honing jigs are undeniably useful, but they often become an impediment to learning professional sharpening skills, and they are more time-consuming to use than freehand sharpening. Jigs can certainly make the sneaky snake of multiple bevels workable, but please don’t ignore the inescapable fact that if one uses a jig properly, over multiple sharpening sessions the result will be… let me think about it…. wait a second while I make a little sketch here…. oh yea, a flat bevel. Hmmm….

Hey, I’ve got an idea. When performing routine sharpening (not the 3 cases listed above), instead of taking shortcuts and adding micro-bevels which turn into secondary bevels and maybe even bulging bevels, why not start with a flat bevel and keep it flat? And then just maybe we could take advantage of the natural indexing properties of that flat bevel to sharpen freehand and save a lot of time NOT polishing skinny secondary bevels or fat bulging bevels? You know what, it just might work!

A honing jig is very helpful for making big angle corrections. I own several, but the Lie-Nielson model is my favorite: I use it every third blue moon. If you decide to use one, however, reserve it for emergency or drastic measures. Don’t let it become training wheels, kiddies.

The Nano-bevel

In this and previous posts we discussed bulging bevels, which are convex bevels on plane or chisel blades; secondary bevels and double bevels, which are additional bevels; and micro-bevels, which are a tiny secondary bevel. But there is another type of secondary bevel a clever Beloved Customer called a “nano-bevel.” I like this term and so will use it, but I caution you that, like all secondary bevels, you should employ this bevel judiciously.

We will go into freehand sharpening techniques in greater detail in future posts, but to avoid confusion when discussing the nano-bevel, we need to touch on some of those techniques now.

You may have noticed that, when sharpening freehand on every stone but the finish stone, most, but not all people do a better job by applying downward pressure on the blade only on either the push stroke away from their body or the pull stroke back towards their body, but not in both directions. This is because placing downward pressure in both directions tends to make the blade rock resulting in a less-than-flat bevel, or Saints preserve us, the demonic bulging bevel. As you can imagine, if this rocking motion gets out of hand on the rougher stones the bevel angle can get out of control quickly.

However, on the finish stone, it is most efficient to apply light downward pressure in both directions. The advantage is that a teeny tiny bit of unintentional rocking helps to ensure the last few microns of the blade’s cutting edge are thoroughly polished. And because the abrasive power of a finish stone is so small, there is no danger the bevel will become rounded, at least if you don’t get carried away. From the wood-shaving’s eye view, this creates a tiny bevel at the last few microns of the cutting edge. This is one example of a “nano-bevel.” Stropping produces the same result on a larger scale. There is also another type of nano-bevel for emergency use.

When using a finish plane on wood with twisty grain you have no doubt experienced frustrating tearout. The usual litany of solutions is to reduce the blade’s projection for finer depth of cut, skew the plane, oil and adjust the chipbreaker, resharpen the blade, adjust the plane’s mouth, or even slightly dampen the wood with a planing fluid such as water, whiskey, or unicorn wee wee. All these methods can help.

On the subject of planing fluid, water works well but dries slowly and can have problematic secondary effects. And unicorn products are dreadfully expensive nowadays, even on Amazon, so I prefer a smooth, inexpensive, industrial-grade busthead. Please ask Ken Hatch for a demonstration and recommendations for a good planing fluid next time he invites you over to his house for his world-famous tacos.

Please note that I don’t drink any planing fluid other than water. Of course unicorn wee wee is more addictive than OxyContin and drives mortals quite mad. And alcohol is yeast pee pee and deadly, but I prefer whiskey for a number of reasons. First, whiskey has a good water/alcohol ratio that wets the wood about the right amount of time and then evaporates cleanly. Too wet and it penetrates too deeply. Too dry and it evaporates too quickly. Isopropyl alcohol works fine too but it is considered a pharmaceutical in Japan and so is very expensive. As with other alcohol products not intended for internal consumption, it contains poisons added at the demand of greedy governments for the sole purpose of maximizing tax revenues. I don’t need those poisons touching my tools or my skin. Whiskey doesn’t contain poisons (other than alcohol, of course), it’s cheaper and smells better.

Another classic solution to reduce tearout of course is to use a plane with a steeper blade bedding angle, but what to do if you don’t have a high-angle plane handy? A traditional, jobsite-expedient solution used by Japanese woodworkers is to create a nano-bevel on the ura side of the blade. This is accomplished during sharpening while polishing the ura on the finishing stone by lifting the head of the blade just a itsy bitsy teeny weeny nat’s nosehair thickness during the final stroke, pulling the blade towards you, of course, creating a “nano-bevel” on the last few microns of the cutting edge at the ura, effectively changing the approach angle of the blade.

Be forewarned that this is only for emergency use, and that if you are careless, or use it too often, the nano-bevel will become a microbevel, your blade will be damaged, efficient sharpening will become impossible, the chipbreaker will cease to function, and the gods of handsaws may curse you so all your hair will fall out and your dog will barf whenever it sees you! Or is it your dog’s hair will fall out and you will barf? I forget.

Now where did I set down that jar of planing fluid….?

Conclusion

A wise man will seek to avoid shortcuts that save a bit of time short-term only to waste more of his time and money long-term. If you simply make the effort to train yourself in basic sharpening skills, pay attention, and keep the bevel flat, time, steel, and stone-wasting monkeyshines such as double bevels will be unnecessary.

We have talked about the cutting edge’s proper shape. Beginning with the next post in this series, we will examine how to use sharpening stones to make it that way. 

YMHOS

Well Dude, I’m done sharpening using my most excellent honing jig for now and am off to the beach on my chick magnet! Don’t wait up, Mom.

Sharpening Japanese Woodworking Tools Part 1

Sharpening Part 2 – The Journey

Sharpening Part 3 – Philosophy

Sharpening Part 4 – ‘Nando and the Sword Sharpener

Sharpening Part 5 – The Sharp Edge

Sharpening Part 6 – The Mystery of Steel

Sharpening Part 7 – The Alchemy of Hard Steel 鋼

Sharpening Part 8 – Soft Iron 地金

Sharpening Part 9 – Hard Steel & Soft Iron 鍛接

Sharpening Part 10 – The Ura 浦

Sharpening Part 11 – Supernatural Bevel Angles

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Sharpening Part 13 – Nitty Gritty

Sharpening Part 14 – Natural Sharpening Stones

Sharpening Part 15 – The Most Important Stone

Sharpening Part 16 – Pixie Dust

Sharpening Part 17 – Gear

Sharpening Part 18 – The Nagura Stone

Sharpening Part 19 – Maintaining Sharpening Stones

Sharpening Part 20 – Flattening and Polishing the Ura

Sharpening Part 21 – The Bulging Bevel

Sharpening Part 22 – The Double-bevel Blues

Sharpening Part 23 – Stance & Grip

Sharpening Part 24 – Sharpening Direction

Sharpening Part 25 – Short Strokes

Sharpening Part 26 – The Taming of the Skew

Sharpening Part 27 – The Entire Face

If you have questions or would like to learn more about our tools, please use the questions form located immediately below. Please share your insights and comments with everyone in the form located further below labeled “Leave a Reply.” We aren’t evil Google or incompetent facebook and so won’t sell, share, or profitably “misplace” your information.

Sharpening Part 20 – Flattening and Polishing the Ura

A mind needs books as a sword needs a whetstone, if it is to keep its edge.

George R.R. Martin

Now that we are geared-up and our sharpening stones are flat, let’s make our blade sharp. The first step in sharpening a new blade is truing the ura. So let’s get to it.

General

All standard chisel blades and plane blades, whether Japanese or Western, need to have a planar flat or ura that it will be in contact with the sharpening stones its full width, and ideally, full length. Perfection is not necessary, however, so don’t let yourself get obsessive. If the ura is arched (concave), for instance, so it is in contact with a flat sharpening stone near the neck of a chisel, or head of a plane blade, and the cutting edge, that may be workable, but it must be in complete contact right behind the cutting edge. I cannot stress this importance of this point too strongly.

Once the ura of your chisel is flat and true, you should not need to true it again unless the blade needs major repairs. Japanese plane blades, on the other hand, are a little more complicated because repeated sharpenings tend to gradually wear out the land right in front of the cutting edge, called the “ito ura,” and the bevel must be tapped-out to compensate, and the ura re-flattened. I won’t delve into the subject of “tapping out” the ura of plane blades in this post but will save it for future discussions about Japanese planes.

Evaluate the Ura

The first step in flattening or truing an ura is to evaluate its condition. Don’t start grinding away willy nilly without first checking it and making a plan. If you find you cannot stop yourself, don’t walk but run to the nearest pharmacy and buy a bucket of the medicine discussed in part 19 in this series about maintaining sharpening stones.

There are several ways to check the ura’s condition. A narrow straightedge works well in most cases. Place the edge on top of the full length of the shiny land at one side of the ura all the way to the cutting edge. Keep the straightedge touching the land; Don’t let it span the hollow- ground urasuki. Hold the straightedge and blade up to a strong light source and look for light passing between them. This technique is quick and dirty and will suffice in most cases, but does not tell you a lot about twist.

Use a straightedge to check the right and left lands for flatness. It doesn’t do any good to span the hollow-ground urasuki, so don’t bother. These photos are taken from above for clarity, but you want to hold the blade and straightedge together up to a strong light to observe any light showing between them that will indicate a gap. I am using a small square, but a simple small straightedge is more convenient. This takes a bit of coordination so be careful not to drop a chisel on your toe. I’ve done this once or twice before. Monkey-football.
This is a 30mm Sukemaru atsunomi, a famous brand and an excellent and powerful chisel hand-forged by Mr. Usui from Shirogami No.1 Steel. It’s in pretty good shape, but can benefit from a little truing as can most new chisels and plane blades.

Another method to check the ura for planar is to paint the shiny lands with dark marking pen ink or Dykem liquid, apply a bit of fine sharpening stone mud to a piece of flat glass, like the piece mentioned in Part 17, and rub the blade’s flat or ura over the glass. The high spots will become obvious. If the ura is banana shaped (convex), mark the high spot with your marking pen. More often than not, the ura of chisels will be generally flat, but the last 6mm or so of the cutting edge will be curved upwards towards the chisel’s face.

I learned two things from my examination of this Sukemaru brand atsunomi. First, there is a high spot (convex) at the skinny land on one side located approximately 1/2 to 5/8 the blades’s distance from the cutting edge. The land on the other side seems a little low. Hmm, curious. This is a bit unusual, but it happens when a blade warps during heat treat, which Shirogami steels tends to do frequently.

The second problem I observed was that the last 3~4mm of the land right behind the cutting edge curves downward away from the ura just a tiny bit, enough to cause problems.

I next need a plan to resolve these problems with a minimum of time and effort and without making things worse.

Make a Plan

The temptation to start grinding away immediately will be powerful. If it becomes too much, take a coffee cup or three of the medicine mentioned above and slather it on your head forcefully. Don’t hold back, for Pete’s sake, rub it in really good now. Some say my excessive use of this medicine is why I am as bald as an egg, but I prefer to believe it is caused by the light radiating from my gigantic brain (ツ). Thank goodness for my aluminum foil skull cap with its protruding copper wires!

Any plan needs goals and objectives. In this case the goal is a perfectly planar ura, but if this goal is difficult to achieve quickly there is an objective you should plan to achieve immediately in any case, one that may make it possible to achieve the larger goal over multiple routine sharpening sessions without any special effort.

As I keep harping, to make a chisel or plane work well, you need a flat area right at the cutting edge. This is where the cutting occurs and the area I need to keep sharp, so I will make creating this flat area the first objective in my plan, and then determine the steps to achieve it. Make certain every step in your plan and every stroke on the stones gets you closer to this objective, not further away. This means working smart.

If the blade is arched (concave), touching at two points, one near the neck of the chisel blade, or head of the plane blade, and at the other at the cutting edge, and not in between, all is well. I recommend you leave a blade like this as-is because after a few sharpening sessions the ura will become flat and twist-free without any special effort, and the blade will become very sharp and be entirely functional.

If the blade is wavy (rare) or banana-shaped (convex), your plan needs to take those details into account.

I located the highest point of the bulging area at the ura and marked a line across it with my marking pen. I then measured halfway between this line and the cutting edge and made another line. This area we will call the “focus line.” It is here where I need to focus the most pressure when grinding down the ura, not the entire length of the blade.

The purpose of doing all this prissy planning and layout work is to protect the right and left side lands from being wasted unnecessarily. Newbies try to work the entire length of the blade, but this is illogical and ignores three points. The first point is that the majority of the metal I need to waste is usually located to the right and left of the land nearest the cutting edge, not the full length of the blade, so there is little benefit to grinding the entire ura. The second point is that the side lands are thin as a blade of grass and will abrade very quickly with almost no effort. Besides, without using large plates and stones, it is very difficult to work the blade’s full length accurately without wearing notches in the side lands anyway. The third point is it makes no sense to try to grind down the land nearest the neck since the plane of the ura hinges on this land. Best to leave it alone and focus my efforts where they will make a difference.

Plane blades don’t even have a land near the head, so the futility of working the entire ura on plane blades is even more obvious than for a chisel.

Work the Plan

The traditional Japanese tool used to flatten and/or correct ura is a smooth steel lapping plate called a kanaban, meaning “metal plate.” To use it, carborundum powder and water are placed on the plate, and the blade is lapped. This is not a difficult process at all, but there is a tendency for the blade’s perimeter to be ground more than the interior areas as the grit is forced in between the kanaban and the blade’s perimeter. To avoid this tendency, and to speed the process up, I prefer to use diamond plates instead of kanaban.

Whatever plan you developed, and whichever tool you selected for this job, the time has come to work the plan. Do you need more medicine? A bigger coffee cup?

First, color the ura’s perimeter lands with a marking pen or Dykem to help you see where the ura is being ground down. Don’t ever guess.

Place the most pressure on the focus line selected above. Move the blade back and forth (not side to side) onto and off of the diamond plate or kanaban with the cutting edge and the focus line always touching the diamond plate or kanaban. Don’t go past the high point for now. Be careful to not grind a notch into the narrow side lands where they meet the edge of the diamond plate or kanaban. Most people make this mistake at first.

Grind the ura down so the line at the highest point and the cutting edge is fairly flat.

Work the blade on and off the edge of the diamond plate using short strokes and without going much past the highest point marked earlier. This works because the right and left side lands are thin and can be abraded in just a few strokes. I have moved my fingers to reveal the lines, but in actuality my fingers will press down hard on the focus line while working the blade.
Using a stick to apply more pressure to the blade. I am holding the end of the stick and the chisel’s handle together in my right hand. This is simply illustrating a technique. This chisel did not actually require this sort of aggressive attention.
The same stick technique works even better for plane blades and makes it easier to apply pressure right behind the cutting edge. When doing this, however, be sure to work the blade both forward and backward while moving it right and left on and off the plate’s edge to avoid digging a trench in the narrow side lands.

Remember, the narrow lands at the sides of the hollow-ground urasuki will abrade down quickly. And the rest of the ura can be gradually flattened during subsequent sharpening sessions using regular sharpening stones. It doesn’t need to be made perfect immediately. What matters most is the steel on the land right at the cutting edge.

The high spot on the land near the top of the photo has been relieved after a few passes on the #400 diamond plate. The side lands are in fair condition, and the land behind the cutting edge (itoura) needs just a little more work.
After a few more passes on the diamond plate, the ura is in good shape. Note the land at the photo’s bottom is not in full contact, but the opposite side is. This is will not impact the blade’s performance, and will work itself out during future sharpening sessions without special attention.
Flattening my stones before using them. Notice I am using two 1,000 grit stones to save time and stones. Don’t neglect flattening your stones, whether you use waterstones, novaculite stones, coticule, or even sandpaper.
Working the ura on the flat 1000 grit waterstone. Did I mention it is flat? Notice that I am working on and off the stone, not side to side, to save the right and left lands. Some but not all strokes are full length. The goal is simply to remove the deep scratches left by the diamond plate.
The ura after polishing on the flat 1000 grit waterstone. At this point the ura is in good shape. Notice how the land at the photo’s left is wider that elsewhere. This increase in width developed because this location was the high spot on this convex ura. Notice how the land on the left side is not even touching the plane in one area. What you should take away from this photo is the realization that if I had focused my efforts on this high location first and ignored the downward curvature of the land nearest the cutting edge, I would have wasted a lot more time and valuable metal only to shorten the useful life of this excellent chisel. Do you see the benefit of carefully checking the ura’s condition, making a plan with clear goals and objectives, and then working the plan? Did the medicine work? Next, we’ll work on the bevel, make a tiny burr, polish it off by making a few strokes alternating from bevel to ura, and be ready for the finishing stone.
Working the bevel on the flat 1,000 grit waterstone. Notice the mud piling up in front of the blade indicating the extreme cutting edge is in contact with the stone. I am applying pressure only on the push stroke to prevent the stone from rocking and developing a “bulging bevel,” A honing jig is not necessary.
The bevel after working on the 1,000 grit waterstone. No jigs were used. No “tricks” involving rulers were used. A silly, inefficient “micro-bevel” was neither wanted nor needed. The bevel is perfectly flat. Flattening the ura and polishing both ura and bevel to this level took less than ten minutes. When the purchaser of this blade eventually dulls the edge, he should not need to spend more than 2~3 minutes to sharpen this blade once his gear is ready, assuming he is able to sharpen freehand.

Polish a blade’s ura up to the level of your finest finishing stone once, and don’t touch it with rougher stones again unless it is absolutely necessary, or further gradual flattening is required. This means that in normal sharpening sessions you must remove all the damage at the cutting edge by abrading the bevel with the rougher stones, and only when the bevel is ready for the finish stone, do you work on the flat or ura, alternating from bevel to flat/ura until all defects, burrs, and even visible scratches are polished away.

If you condition the flat (ura) side of the blade correctly, and keep it polished, you should not need to work it on anything but your finish stone until it is time to tap out and grind the ura or back in the case of plane blades. Therefore, the bevel side of the blade is where we spend most of our time and effort.

Now that the ura is in good shape, we will look at sharpening the other side of the wedge, the blade’s bevel, in the next post in the series.

YMHOS

Links to Other Posts in the “Sharpening” Series

Sharpening Japanese Woodworking Tools Part 1

Sharpening Part 2 – The Journey

Sharpening Part 3 – Philosophy

Sharpening Part 4 – ‘Nando and the Sword Sharpener

Sharpening Part 5 – The Sharp Edge

Sharpening Part 6 – The Mystery of Steel

Sharpening Part 7 – The Alchemy of Hard Steel 鋼

Sharpening Part 8 – Soft Iron 地金

Sharpening Part 9 – Hard Steel & Soft Iron 鍛接

Sharpening Part 10 – The Ura 浦

Sharpening Part 11 – Supernatural Bevel Angles

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Sharpening Part 13 – Nitty Gritty

Sharpening Part 14 – Natural Sharpening Stones

Sharpening Part 15 – The Most Important Stone

Sharpening Part 16 – Pixie Dust

Sharpening Part 17 – Gear

Sharpening Part 18 – The Nagura Stone

Sharpening Part 19 – Maintaining Sharpening Stones

Sharpening Part 20 – Flattening and Polishing the Ura

Sharpening Part 21 – The Bulging Bevel

Sharpening Part 22 – The Double-bevel Blues

Sharpening Part 23 – Stance & Grip

Sharpening Part 24 – Sharpening Direction

Sharpening Part 25 – Short Strokes

Sharpening Part 26 – The Taming of the Skew

Sharpening Part 27 – The Entire Face

If you have questions or would like to learn more about our tools, please use the questions form located immediately below. Please share your insights and comments with everyone in the form located further below labeled “Leave a Reply.” We aren’t evil Google or incompetent facebook and so won’t sell, share, or profitably “misplace” your information.

Sharpening Part 16 – Pixie Dust

Ashes to ashes, dust to dust, if the women don’t get you then the whiskey must.

Carl Sandburg
Related image

In the previous post we examined sharpening stones, the minimum set I recommend, those I typically use, and the most important stone in any set. In this post we will shift our focus to things that can go wrong when sharpening, including supernatural influences.

Dust Contamination

As I mentioned in the previous post in this series I almost never take a 10,000+ grit synthetic finishing stone or natural finishing stone to jobsites. This decision is based on observation under practical conditions: Jobsites are rough and dirty places, and stones are fragile. 

Iron Pixies are rabid fans of Lingerie Football. Don’t hang posters or watch games in your workshop if you want to avoid crowds of the tiny beer-drinking fiends.

Even if Murphy is drunk and the Iron Pixies are distracted watching Lingerie Football on the boob tube (pun intended), airborne dust at the jobsite will always instantly degrade an expensive 12,000 grit rated stone to an effective 4,000 grit or less in an instant, making a fragile, expensive, ultra fine-grit stone pointless. How clean is your workplace? Something to think about. Seriously.

This is not just a theory that sprouted from my overactive imagination like a dandelion on a dung pile, but is scientifically verifiable. Give it try.

Get out your microscope or high-power loupe. Place a clean glass slide near where you will be sharpening. 60 minutes later, examine the slide and count the dust specks. How did they get there? Dust is in the air quite naturally, but vehicular and foot traffic kick up lots more.

Most of those dust specs are larger and harder than the grit that makes up your finishing stone. Imagine what happens to your blade when those pieces of relatively large, hard grit get mixed into the stone slurry, or become embedded into the stone’s surface. Not a pleasant thought.

Related image

Dust contamination even has historical precedence. Japanese sword sharpeners traditionally do their best work during the rainy season when there is less dust in the air to contaminate their stones. 

Professionals that polish pianos, stone, glass and jewels are also sticklers for eliminating dust contamination.

Just design and build a few cleanrooms for picky customers with SEMs (scanning electron microscopes), or with lens coating equipment, or who make pharmaceuticals and you will get an education about dust and the problems it creates quickly.

What dust do we find at construction job sites or workshops? First, assuming we are working at a building project, there are exterior sources of dust. Unlike a house, the doors and windows are usually open to gain maximum circulation, even when dusty landscaping operations are ongoing and trucks carrying materials and garbage are running everywhere kicking up clouds of dust.

effects of dust on lungs

Second, unless you have the jobsite entirely to yourself, there are usually other trades inside the building grinding, sanding, cutting and walking around kicking dust into the air too. The most pernicious dust on the jobsite is drywall and joint compound. This white fluffy dust appears harmless, but it contains tiny granite silica particles harder than steel, that float around and settle on everything. They are a health hazard that has put more than one person in the hospital with respiratory problems. They will contaminate your sharpening stones.

Sandpaper, sanding discs, grinders and angle grinders also spray millions of tiny hard particles everywhere, many of which float in the air and can travel some distance before settling, especially inside an enclosed building or workshop.

dangers of dust on site

Does your business or home workshop have a large door facing a public road with cars and trucks going back and forth? Do people with muddy boots come in and out? Are dirty pallets with piles of dirt hidden on the bottom boards offloaded inside? Do you use sanders or grinders in your workshop?

If you are sharpening outside, or at a dusty jobsite, or inside a dusty workshop, and especially if you regularly use sanders and grinders there, I recommend the following procedures before you use fine-grit stones:

  1. Try to locate your sharpening area away from foot traffic, grinding and sanding operations, and dusty areas;
  2. Sweep the surrounding floors well, since it is the movement of feet that billows settled dust back up into the air, and wait at least 15 minutes after sweeping for the dust to settle before sharpening;
  3. Wet the surrounding ground or floor with water to keep the dust down (this makes a big difference);
  4. Lay a clean cloth or a sheet of clean newspaper over your fine stone when you are not using it for more than a couple of minutes to prevent airborne dust from settling on it;
  5. Keep your fine stone wrapped in a clean cloth or newspaper when you are not using it;
  6. Scrub your fine stone under running water with dishwashing soap (neutral PH) and a clean natural-bristle brush before each use to remove dust and embedded grit.

And for heaven sake, even if you can’t take your benchdogs with you everywhere, at least have a brass bevel angle gauge in your toolkit, and use it everytime you sharpen, to keep the pernicious pixies at bay. I hang mine around my neck from a red string, red because all species of the Little Folk strongly dislike that color. It’s no coincidence that Iron Pixies take great joy at turning valuable tools red.

The following are few references regarding silica and construction dust: Silica-Safe.org Center for Disease Control. Makes you want to wear a respirator in bed.

The legal team hard at work digging up dirt

YMHOS

Links to Other Posts in the “Sharpening” Series

Sharpening Japanese Woodworking Tools Part 1

Sharpening Part 2 – The Journey

Sharpening Part 3 – Philosophy

Sharpening Part 4 – ‘Nando and the Sword Sharpener

Sharpening Part 5 – The Sharp Edge

Sharpening Part 6 – The Mystery of Steel

Sharpening Part 7 – The Alchemy of Hard Steel 鋼

Sharpening Part 8 – Soft Iron 地金

Sharpening Part 9 – Hard Steel & Soft Iron 鍛接

Sharpening Part 10 – The Ura 浦

Sharpening Part 11 – Supernatural Bevel Angles

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Sharpening Part 13 – Nitty Gritty

Sharpening Part 14 – Natural Sharpening Stones

Sharpening Part 15 – The Most Important Stone

Sharpening Part 16 – Pixie Dust

Sharpening Part 17 – Gear

Sharpening Part 18 – The Nagura Stone

Sharpening Part 19 – Maintaining Sharpening Stones

Sharpening Part 20 – Flattening and Polishing the Ura

Sharpening Part 21 – The Bulging Bevel

Sharpening Part 22 – The Double-bevel Blues

Sharpening Part 23 – Stance & Grip

Sharpening Part 24 – Sharpening Direction

Sharpening Part 25 – Short Strokes

Sharpening Part 26 – The Taming of the Skew

Sharpening Part 27 – The Entire Face

If you have questions or would like to learn more about our tools, please use the questions form located immediately below. Please share your insights and comments with everyone in the form located further below labeled “Leave a Reply.” We aren’t evil Google or incompetent facebook and so won’t sell, share, or profitably “misplace” your information.

Sharpening Part 15 – The Most Important Stone

Orders are nobody can see the Great Oz! Not nobody, not nohow! 

Gatekeeper, Emerald City

Many people high-center on the question: “What is the best way to sharpen my tools?”

I was hesitant to publish this series of posts about sharpening because, beginning with this post, I must answer this question by writing about tools and techniques that contradict many people’s sharpening religion. Some of those people will doubtless become emotional. As Benny Franklin once famously said: Ça ira, ça ira.

The objective of this post is to help our Beloved Customers properly maintain, sharpen and use the blades they purchase from us. Nothing else.

This post will not be a sharpening tutorial; that will be a future post.

We will examine the process of sharpening woodworking tools using mostly waterstones. We will touch on the motivations, goals and priorities related to sharpening you should consider, the minimum set of sharpening stones I recommend, and my suggestion for the most important stone in your arsenal, one you must be proficient in using.

Motivations

The Great and Powerful Oz has spoken!

You might have noticed from my previous posts that I like to understand motivations. Am I cynical? Perhaps, but where there are smoke and lights presented and money to be made, there is almost always someone behind the curtains spinning dials and pumping pedals. Oooh, pretty lights!

Anyone who does anything has a motive for doing it, and knowing that motive can help us evaluate the validity, and sometimes even the honesty, of what they do, say and write on a particular subject. How can we best ascertain the motivations of those advocating various sharpening methods and related accoutrements? Here are some simple questions you might want to ask: Are the promotions or promoters touting sharpening stones or other stuff they might profit from? Are they selling books on sharpening? Do they teach classes on sharpening? Do they have “sponsors” or “patrons” that supply them, at no cost or with large discounts, stones, diamond paste, sandpaper, sharpening machinery, and/or honing contraptions in exchange for promoting those goods? Are they “influencers” (yes, that’s a real vocation in the YouTube World) who are compensated for clicks? Do they publish reviews on products they receive for free? You see the pattern.

Regardless of their business model or motivations, many people give good advice. But some are shills, while some others are pretenders, and their advice will be colored accordingly. Caveat emptor, baby.

And then there is the most obvious motivation. After all, it doesn’t cost even $20 to make a Mechaultrasuperfine Ninja-purple Gold-dust-infused Musashi Walk-on-Waterstone that retails for $650. And have you calculated the long-term equivalent cost of diamond paste and abrasive films? Somebody’s making serious cash.

Just once I’d like to cross the road without having my motives questioned…

Whatever stones you select, I urge you to find a good balance of performance vs cost vs time vs sustainability, with sustainability referring to both the amount of landfill-stuffing the selected process creates as well as its long-term effect for good or ill on your blades. This 4-variable calculus depends not only on the characteristics of the stones and blades you use, but on your sharpening skills too, so it may take years to find the inflection points if you take a scientific approach. The quadratic formula does not yield useful results, sorry to say.

At one time or another I have tried and tested many popular sharpening “systems” including those that rely on jigs, machinery, sandpaper, plastic films, stick, liquid, paste, and powdered abrasives, buffers, strops and even superflat ceramic plates. I enjoy learning new things. They all get the job done, and all have serious merits, but to reduce the time and brain damage involved in this calculus, a wise man will learn from professionals, people who have been down the road before and actually use tools to feed their families, and who have no conflict of interest, be it stones, books, or clicks. That’s what I finally did, and I think it worked out well. But I need to issue a disclaimer before we go further.

Disclaimer

Here it is in red letters.

I say what I believe and believe what I say, even if it offends the “gurus” of sharpening. I buy their books and DVDs, watch their YouTube videos, and try the sharpening techniques and even the “tricks” they recommend, so I like to think I am not a “frog in a well,” as the Japanese saying goes. If I don’t know something, I will say so. I am not a child to be offended if you disagree with me, but I ask you to not become orcish.

Please note that we do not now and have never received goods, discounts, or financial compensation of any kind from anyone in exchange for modifying our opinion about sharpening tools and techniques.

I have personally taught many people how to sharpen tools over the years, but have never received a red cent for my time and haven’t used those training sessions as an excuse to sell stuff.

I have never done a product review.

I have never written a book or magazine article or even a blog post with advertiser support.

Please note that the document you are currently reading cost you nothing, was written and paid for by C&S Tools alone, and that there are no banners, commercials, or outside links on any of the pages in this blog. No SEO strategy at all. If Evil Google brought you here, it was not at our bidding.

We want to help our Beloved Customers, mostly professional woodworkers who already possess a certain level of skill, to level-up those skills. C&S Tools has no commercial incentive to mislead, and will not do so. But we do have a profit motive.

Remember, we have a 100% guarantee on the materials and workmanship of the tools we sell, so our sole financial motivation, and the very reason for this blog, is to help our Beloved Customers understand the tools we sell, and to become proficient in sharpening, maintaining, and using them so they won’t mistake a lack of skill and/or experience on their part as a problem with the tool. All most professionals really need is a little guidance. We want ecstatic customers because they become repeat customers. And we do hate to disappoint.

Goals, Objectives and Priorities

I mentioned 4 variable calculus above. Actually, it’s more like 5 variable calculus, the fifth variable being your goals and objectives for sharpening. Let’s examine those in more detail.

If satisfying curiosity are among your goals, then by all means try all the stones, sandpaper, films, pastes, jigs, contraptions, and machines available and methodically test them until they turn to dust. It simplifies the calculus, but the cost and time required to reach a final conclusion may become a heavy burden.

If beautiful blades, zen-like sharpening experiences, and improved hand-soul coordination are high among your ojectives (they’re included in mine), then you will want to try natural finishing stones. I heartily recommend them to those who have reached a certain level of skill with synthetic stones and are willing to roll the bones.

The performance of the sharpening system you select, including the following factors, is something should include in your calculations:

  • Time efficiency: How long does it take you to produce an adequately sharp edge starting from a dull/chipped one? How fiddly is the process? For this calculation you will need to determine how much your time is worth. Remember, while you may enjoy sharpening, from the professional’s viewpoint, time spent sharpening is non-productive time because, during the period you are working on tools, your hands, eyes, and mind cannot work on the stuff you contracted to deliver to the Customer;
  • Cost efficiency: How many billable hours and expensive supplies/tools/equipment must you expend to obtain an adequate cutting edge? For this calculation you will need to determine the cost of time, consumables (stones, sandpaper, film, paste, powder, beer) and equipment (grinders, jigs, plates, widgets, etc.) expended in producing an adequate cutting edge long-term. Even if you are not getting paid for your woodworking, your time still has value. And don’t forget to depreciate the cost of stuff. This is where synthetic waterstones shine in comparison to the many other sharpening systems out there.
  • Cutting efficiency: How well and how long does the sharpened blade cut? For this calculation, you need to determine what an “adequate cutting edge” is for you. For instance, given the same abrasives and expending the same amount of time to sharpen two blades, the blade with a rounded bevel, or even multiple bevels, is seldom as sharp as the blade with a simple flat bevel, as can be readily confirmed using a powerful loupe or microscope to examine the last few microns of the blade’s effective cutting edge (more on this subject in Part 21 of this series). Does the sharpening system you are testing tolerate or even promote bulging bevels or multiple bevels? Get out your loupe before your inner troll makes you say things you will regret.

If curiosity, pleasure and beauty are lower priority than practical performance in your list of objectives, then I suggest you focus on synthetic waterstones and the bedrock basics, at least for now:

  1. Obtain a minimum set of basic synthetic stones, or adapt what you already have;
  2. Learn how to use them skillfully;
  3. Practice those skills until they seep into your bones.

It is not an expensive process, but neither is it the instant short-term sort of thing the Gurus of Sharpening offer in their books and DVDs and classes through their tricks and gimmicks. It takes real skills that will serve you and your tools well for your entire life. And it all starts with the minimum set of stones.

The Goldilocks Set

Related image
Oh my goodness, just look at the time! I really must be going.

Sharpening stones are expensive consumables that disappear a little with every stroke. If you need more than 5 minutes to sharpen a plane or chisel blade that was not chipped or damaged, then you may be spending too long, and wasting your time and stones, so it’s important to determine the bare minimum set of stones that work best for you.

The Goldilocks set I recommend includes the following 4~5 stones/plates:

  1. A Rough Stone: 400~800 grit rough diamond plate or two carborundum stones;
  2. Medium Stones: Two 1,000 grit waterstones (I will get into the reasons for having two stones of the same grit in another post);
  3. A Finish Stone: 6,000~8,000 grit waterstone.

Please also note that I don’t take 10,000+ grit synthetic finishing stones or natural fine-finishing stones to jobsites. This decision is based on simple practical experience: Jobsites are rough and dirty places, and stones are fragile. 

But there is an even more important reason: Airborne dust at jobsites will instantly degrade an expensive 10,000 grit rated stone to an effective 4,000 grit or less in an instant, making ultra-fine grit stones pointless. Dust will be the subject of the next post in this series.

The sharpening stones I normally use in the shop include a few beyond the minimum set described above. This set includes more stones, but the idea is that this finer gradation creates a better-quality cutting edge while consuming less of my expensive finishing stones. Natural stones can be pricey:

The packaging is fancier, but the content’s the same.
  1. One 400~800# diamond plate or two rough carborundum stones (only occasionally necessary);
  2. Two 1000# Imanishi waterstones (Bester brand) (usually necessary, but sometimes I skip it);
  3. Two 2000# Bester waterstones;
  4. One 6000# stone (fine enough for quickly finishing chisels and most planes);
  5. Two natural stones for finish planes and push chisels, or just for fun (a 10,000# synthetic stone works just as well).

Which Brand of Synthetic Stone?

I don’t think there is a dime’s worth of difference between the various synthetic stone manufacturers except for their marketing and distribution. I use what works for me and is available locally at the cheapest price. We don’t sell stones and have no relationship with or loyalty to any manufacturer. 

Regardless of manufacturer, I do recommend you avoid the extra-thick variety of synthetic stone because the oven’s heat sometimes does not penetrate deep enough leaving the interior too soft.

The Most Important Stone

Everyone focuses like a laser on the finishing stone, the final stone in the process, but when sharpening a particular blade, the most important stone is really the first stone you use in the series, be it a 400 grit diamond plate or a 2,000 grit waterstone. 

You may find this whole discussion passing strange, so I will explain. The roughest stone (or diamond plate, depending on the amount of steel that must be wasted and your available time and budget) you begin the sharpening process with builds the foundation of your cutting edge by performing the following two critical tasks:

  1. Removing damage at the cutting edge; and
  2. Shaping/flattening the cutting bevel.

Only a rough stone (400~800 grit) can accomplish the first task efficiently. If the truth of this statement is not self-evident, I won’t even try to convince you. Do the comparisons yourself: count strokes, time, and cost, measure angles, and peep at scratches through a high-power loupe.

In addition, your roughest stone or diamond plate is also the most efficient tool for shaping the bevel and cutting edge, if it needs to be adjusted. Until these two critical tasks are completed, none of the subsequent finer stones can accomplish anything efficiently, and the faster and more precisely these two tasks are accomplished the sooner one can stop sharpening and get back to the real job of woodworking.

The role of the finer stones in the sharpening sequence is simply to replace the deeper scratches left by the preceding rougher stone with progressively finer scratches. And since this work is done using more expensive, less-abrasive and slower-working stones, it is most cost/time-efficient to accomplish this task as quickly as possible. If you knock out the two foundational tasks listed above using your rough stone/plate well, then you can accomplish the subsequent polishing work at minimum cost and maximum speed. Screw it up and your blades will hate you.

Please be sure you understand the meaning of the previous 4 paragraphs. They are the heart of this article

So how does this work in real life? If the blade is chipped, dinged, or needs shaping, then I start repairing and reshaping the cutting edge’s foundation with my diamond plate. A carborundum stone, if very flat and kept flat, will work too. If my blade is only dull, but not damaged, and the bevel is in good shape, I start with a flat 1,000 grit stone. If the blade is starting to lose its edge, but is not damaged and still cuts, I start the process with a flat 2,000 grit stone. Notice the word “flat” is used a lot in this paragraph.

The objective, again, is to create an adequately sharp edge in the minimum amount of time and cost by starting the sharpening process with the cheapest, most aggressive stone appropriate to the blade’s condition for the heavy wasting and shaping thereby creating a bevel and cutting edge which you can then quickly polish to the final cutting edge using the more expensive, finer-grit stones. Wow, that’s a mouthful!

I want to make one thing perfectly clear before ending this post. Except for a few special situations, I don’t recommend using secondary bevels or micro-bevels except in special circumstances because, like training wheels on a bicycle, they are not an efficient long-term solution. In fact, they are a short-cut that has stunted many people’s sharpening skills. We will return to this subject later. 

YMHOS

This image has an empty alt attribute; its file name is tenor.gif
The Marketing Department

Links to Other Posts in the “Sharpening” Series

Sharpening Japanese Woodworking Tools Part 1

Sharpening Part 2 – The Journey

Sharpening Part 3 – Philosophy

Sharpening Part 4 – ‘Nando and the Sword Sharpener

Sharpening Part 5 – The Sharp Edge

Sharpening Part 6 – The Mystery of Steel

Sharpening Part 7 – The Alchemy of Hard Steel 鋼

Sharpening Part 8 – Soft Iron 地金

Sharpening Part 9 – Hard Steel & Soft Iron 鍛接

Sharpening Part 10 – The Ura 浦

Sharpening Part 11 – Supernatural Bevel Angles

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Sharpening Part 13 – Nitty Gritty

Sharpening Part 14 – Natural Sharpening Stones

Sharpening Part 15 – The Most Important Stone

Sharpening Part 16 – Pixie Dust

Sharpening Part 17 – Gear

Sharpening Part 18 – The Nagura Stone

Sharpening Part 19 – Maintaining Sharpening Stones

Sharpening Part 20 – Flattening and Polishing the Ura

Sharpening Part 21 – The Bulging Bevel

Sharpening Part 22 – The Double-bevel Blues

Sharpening Part 23 – Stance & Grip

Sharpening Part 24 – Sharpening Direction

Sharpening Part 25 – Short Strokes

Sharpening Part 26 – The Taming of the Skew

Sharpening Part 27 – The Entire Face

If you have private questions or would like to learn more about our tools, please use the questions form located immediately below. Please share your insights and comments with everyone in the form located further below labeled “Leave a Reply.” Your information will remain confidential (we’re not evil Google or incompetent facebook).

Sharpening Part 13 – Nitty Gritty

“The true mystery of the world is the visible, not the invisible.” 

Oscar Wilde

In this post we will dig into a few important nitty gritty points about sharpening stones everyone needs to know. Perhaps you already know all these points, but please ready your shovel because there may be at least one buried surprise.

A Flea’s-Eye View

When seen under high-magnification, the surface of a sharpening stone looks like millions of densely-packed stones embedded in a flat field. The smaller the stones, the finer the grit.

As the blade is pushed and pulled over these stones, they scratch and tear metal from the blade’s surface leaving behind scratches corresponding to the size of these small stones. This violence continues until the blade’s ura and bevel form a clean intersection of two planes.

A view of a blade sharpened with 1200 grit diamond plate showing the furrows left by individual pieces of grit

Seen under high-magnification, the cutting edge is jagged where these furrow-like scratches terminate at the cutting edge. To some degree, it may even look like a serrated sawblade. Some blades, like kitchen knives and swords, are used in a slicing motion to cut soft materials like meat and vegetables and enemy arms, and their performance benefits from a serrated cutting edge more than a highly-polished edge, and so do not need to be highly polished on fine-grit sharpening stones. 

Plane and chisel blades, however, are used to cut wood, a material typically harder than foodstuffs, in a straight-on direction, not in a slicing motion, for the most part. In this situation, a rough, serrated cutting edge is weaker than a highly polished edge because the jagged edges are projecting out into space like the teeth of a handsaw blade, and are relatively unsupported and more easily damaged than a highly-polished blade with smaller, more uniform scratches terminating more cleanly at the cutting edge. 

Therefore, in order to produce a sharp durable blade, we must make the microscopic cutting edge smoother and more uniform by using progressively finer grit stones to produce shallower and narrower scratches, and a thin, uniform cutting edge.

But how fine is fine enough? There is a curious phenomenon related to friction that is applicable to cutting edges, and is useful to understand. 

The Friction Paradox

Imagine a cube of heavy stone with its downward flat face resting on the level, flat surface of a larger slab of similar stone. Let’s say it takes some specific measure of force pushing horizontally on the stone cube to overcome the static force of friction between the two stone surfaces in order to make the cube start moving. 

If we gradually increase the degree of polish between the two contact surfaces and measure the force required to start the cube moving at each progressively higher level of polish, we will find the force decreases with each increment of increased polish, for a time. This is at least partially because the irregularities between the two surfaces (asperities) do not interlock as deeply when the surfaces become more polished. 

However, at some point, more polishing brings the surfaces of the two stones into such intimate contact that the molecular attraction between them, and therefore the force necessary to move the cube, actually increases. 

The Inflection Point

The same phenomenon occurs with tool blades. If you sharpen and polish your blades past a particular point, the friction and heat produced between blade and wood will increase, as will the energy that must be expended, while the resulting quality of the cut and durability of the cutting edge will not improve significantly. Of course, the time and money invested in stones spent sharpening past this point will be mostly wasted.

The inflection point where additional polishing yields increased friction with little improvement in cut quality will depend on your tool and the wood you are cutting, but you can gain a pretty good idea of where it is if you pay attention over time. While the sharpening stone manufacturers hate my saying it, in my well-informed opinion there is little practical gain, beyond self-satisfaction, to be had from sharpening chisels or planes past 6,000~8,000 grit, making this range of grit an inflection point in my mind. What about you?

Conclusion

I encourage you to conduct your own experiments to determine the inflection point in the case of your planes and wood you cut. Many who figure this out save themselves significant amounts of time and money sharpening over the long-term.

To those of our Gentle Readers that love sharpening more than woodworking, and enjoy putting money in the pockets of sharpening stone manufacturers more than keeping it for themselves, I apologize for pointing out the floater in the punch bowl. But you probably would have it noticed it eventually anyway, if only from the taste difference.

I will touch more on this important point in the next exciting installment in this scientificish adventure.

YMHOS

Links to Other Posts in the “Sharpening” Series

Sharpening Japanese Woodworking Tools Part 1

Sharpening Part 2 – The Journey

Sharpening Part 3 – Philosophy

Sharpening Part 4 – ‘Nando and the Sword Sharpener

Sharpening Part 5 – The Sharp Edge

Sharpening Part 6 – The Mystery of Steel

Sharpening Part 7 – The Alchemy of Hard Steel 鋼

Sharpening Part 8 – Soft Iron 地金

Sharpening Part 9 – Hard Steel & Soft Iron 鍛接

Sharpening Part 10 – The Ura 浦

Sharpening Part 11 – Supernatural Bevel Angles

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Sharpening Part 13 – Nitty Gritty

Sharpening Part 14 – Natural Sharpening Stones

Sharpening Part 15 – The Most Important Stone

Sharpening Part 16 – Pixie Dust

Sharpening Part 17 – Gear

Sharpening Part 18 – The Nagura Stone

Sharpening Part 19 – Maintaining Sharpening Stones

Sharpening Part 20 – Flattening and Polishing the Ura

Sharpening Part 21 – The Bulging Bevel

Sharpening Part 22 – The Double-bevel Blues

Sharpening Part 23 – Stance & Grip

Sharpening Part 24 – Sharpening Direction

Sharpening Part 25 – Short Strokes

Sharpening Part 26 – The Taming of the Skew

Sharpening Part 27 – The Entire Face

If you have questions or would like to learn more about our tools, please use the questions form located immediately below. Please share your insights and comments with everyone in the form located further below labeled “Leave a Reply.” We aren’t evil Google or incompetent facebook and so won’t sell, share, or profitably “misplace” your information.

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Even monkeys fall from trees (猿も木から落ちる)

Japanese saying
A famous wood carving of 3 monkeys located at Nikko Toshogu Shrine post resconstruction that illustrates a famous saying originating in China that also works as a pun in the Japanese language. From right to left: See no evil; Speak no evil; Hear no evil (見ざる、聞かざる、言わざる).

Ideally, a tool blade will have absolutely uniform dimensions: the right thickness and taper, perfect cross-sections, uniform curvature, and straight edges and surfaces. However, professional grade Japanese tools are not made on CNC machines, but are hand forged, and have dimensional imperfections. Indeed, imperfections are part and parcel of all human endeavors. Most imperfections don’t matter; Sometimes they make the tool better; Other times they need to be remedied.

You, Gentle Reader, may not notice that the blade or cutting edge of one of your chisels or planes is “skewampus,” and consequently the cutting results are less than ideal. You may blame those poor results on your technique in using the tool or the irregular wood grain, when the real problem is the shape of the blade’s cross-section, or your unintentionally sharpening the blade with a skew. We will examine this problem in this post.

We will also look at the curved or “cambered” cutting edge profile in plane blades, the benefits and undesirable results it can produce, and how to incorporate this blade profile intelligently into your woodworking repertoire.

Many people, like monkeys in trees, learn bad habits from their friends and teachers. We hope this post will help you understand what is going on with your woodworking blades, and how to shape and sharpen them intelligently instead of just monkeying around. Please be sure to BYOB (bring your own bananas).

A serious craftsman doing Fine Woodworking in a Pixie-free workshop (notice the strategically-placed boots).

Dealing With Skewampus Blades

Skewampus is an interesting word I learned from my mother. I am told it is a combination of the word “Cattywampus” meaning “in disarray,” and “askew.” I think it is the perfect word for describing the ailments some blades suffer.

While less than ideal, it is not unusual for the thickness of a chisel blade’s cross section to vary slightly across its width, with one side being thicker than the other, forming an irregular quadrilateral cross section. This irregularity is found in plane blades too, but it is not typically a problem. Since there is more steel on the thicker side, the cutting edge will tend to develop a skew during sharpening.

Japanese plane and chisel blades are formed by laminating a layer of hard steel to a much softer body made of extremely low-carbon steel or iron. If the lamination exposed at the cutting edge is not uniform, the area of the blade with more hard steel touching the sharpening stone will abrade slower than areas with less exposed hard steel such that the cutting edge will tend to become skewed during sharpening. Perfection is not required, but the uniformity of the lamination is an important detail to observe when purchasing Japanese tools.

Likewise, Western plane and chisel blades that are not uniformly heat-treated, and that exhibit differential hardening across the bevel’s width, will also tend to become skewed during sharpening as one side of the bevel abrades quicker than the other. This problem is more common than you might imagine, especially in the case of inexpensive tools where appearance and low price are given higher priority than quality.

Anyone that has experience bidding high-dollar construction projects will understand the statement “the most profitable job may be the one you lose.” Cheap tools are much the same way: that low-cost chisel or plane may look good on paper, but if you count your time worth anything, if you dislike headaches, and real-world performance matters to your bottom line, then such a tool is often disastrous. Caveat emptor, baby.

A chisel or plane blade that has an irregular cross section or a skewed cutting edge may not be a problem for many cutting operations. However, when cutting mortises, a chisel blade with a skewed cutting edge or irregular cross section will tend to drift to the side gouging the mortise’s walls and ruining tolerances. If you find that your mortise walls are gouged, or that tolerances are poor, check your chisel blade’s shape, and correct any deformities.

Like all human work spaces, Japan’s smithies are not immune from pixie infestation despite annual blessings by Shinto priests and periodic offerings of rice, salt and wine to the spirits. In a previous post we discussed supernatural predators, so I will refer you to it for antidotes to pernicious pixie pox. But the deformities we are examining in this post are more often the natural result of the human eye misjudging hammer blows or non-judicious use of grinder wheels rather than precocious pixies at play.

If your blade’s deformity is not excessive, you can compensate by applying a little extra pressure on the blade’s thicker side while sharpening it. 

It is interesting how a little off-center pressure on a blade being sharpened over many strokes can change its shape. Many people unintentionally deform their cutting edges by not paying attention to the amount and location of the pressure their fingers apply. A word to the wise.

Another potential solution is to skew the blade in relation to the direction of travel when sharpening the bevel. This works because the leading corner of a skewed blade is abraded quicker than the trailing corner. But once again, inattention causes many people to skew their blades when moving them around on their sharpening stones unintentionally creating, instead of intentionally correcting, skewed cutting edges. There is nothing wrong with skewing the blade when sharpening so long as you are aware of the distortion this practice can produce and compensate accordingly. Another word to the wise.

If these methods don’t compensate adequately, you may want to grind and lap a chisel blade to a more uniform cross-sectional shape. A chemical bluing solution used afterwards will help conceal the shiny metal exposed by this operation if your chisel objects to the shiny spots. Some of them can be quite vain, you know.

A chisel with a an adequately uniform lamination and cross-section, and nice polish.

Cutting Edge Profiles

Many people have access to electrical jointers and planers, but relatively few have industrial equipment with the capacity to dimension wide boards such as tabletops. And of course architectural beams and columns are typically too long or too heavy to dimension with most stationary electrical equipment.

The choices available to most people for dimensioning such materials therefore are either handheld electrical power planers and/or sanders, or axes, adzes and hand planes. Powerplaners, sanders, axes and adzes are beyond the scope of this article, but we will look at hand planes.

I need more than one plane? You can’t be serious!

Although the very idea gives some woodworkers vapors (I don’t mean gas), an efficient craftsman will have multiple planes with cutting edges honed to profiles matched to specific operations.

Everyone that dimensions larger pieces of lumber by hand needs a plane with a wide mouth and a curved or “cambered,” cutting edge called a “scrub plane” in the West, and “arashiko kanna” in Japan.

This variety of plane excels at hogging a lot of wood quickly when the craftsman needs to significantly reduce the thickness of his lumber.  If the blade is narrow and curvature is deep, this plane will hog wood quickly, but leave a deeply rippled surface, often with bad tearout.

One might also have a second arashiko, or jack plane with a wider blade with a shallower curvature for the next steps in the dimensioning process. Such a plane will not hog wood as quickly, but it will produce a surface that is closer to flat and smooth and with less tearout. You can see the advantage of having two arashiko planes, or a scrub plane and a jack plane, with different cutting edge profiles when dimensioning lumber.

Many Gentle Readers use electrical-powered planes to dimension lumber before turning it into furniture, doors, chairs, or sawdust, etc. and are aware that planers always leave tiny ripple-like scallop cuts on the wood’s surface, along with some tearout. This will not do as a final surface. A hand-plane finish is far superior, but it doesn’t make sense to remove any more than the bare minimum of wood necessary to remove the washboard.

A finish plane is the perfect tool for this job on condition that it is sharp, set to a fine cut, the chipbreaker is tuned and set properly, the blade profile is appropriate for the width of the wood to be finished, and the wood does not have too many large knots. In one or two passes such a plane can easily remove the ripples and leave the wood clean and shiny without changing its dimensions much at all.

Assuming the wood is cooperative and one knows how to sharpen and setup their plane properly, blade profile frequently remains a key factor many fail to grasp. Obviously, the curved cutting edge of a scrub plane cannot produce the perfectly flat surfaces required for joining two pieces of wood together. On the other hand, the corners of a perfectly straight blade will leave clearly visible steps or unsightly tracks on the surface of a board wider than the blade, which is not a problem when rough dimensioning a board, but is painful to see if the board’s surface is to be left with just a planed finish.

So how do we solve this conundrum? When finish planing, the professional approach is to use two planes each with a different cutting edge profile. The first type of finish plane has a perfectly straight cutting edge used to plane pieces narrower than the blade’s width. Since the blade’s corners are not riding on the wood while cutting it, they won’t leave tracks and ridges.

The second type of finish plane found in the professional’s toolkit has a curved cutting edge, or more correctly, curved just at the corners to prevent it from leaving tracks and ridges when planing boards wider than the blade. Nearly all the edge is left straight, but creating this tiny amount of curvature at the right and left corners causes it to smoothly disappear into the plane’s mouth so no tracks are made and any ridges are nearly impossible to see or feel. In other words, the corners of the cutting edge never touch the surface of the board, and so don’t leave discernible tracks or ridges. The finer the cut made the smaller any ridges created will be. Indeed, where a high-quality surface is required, the final cut with the finish plane will produce shavings thin enough to see one’s fingerprints through.

You may want to reread the previous two paragraphs to make sure you understand what these two cutting edge profiles are and what they can accomplish before you read further.

Naturally, a professional doing high-quality work needs at least two finish planes, one with a straight cutting edge used to produce flat, precisely-dimensioned surfaces on wood narrower than the blade’s width, and another finish plane with a cutting edge very slightly curved at the corners used to finish wider surfaces.

There are those that advocate using a curved blade, sometimes dramatically “cambered” as some call them, for all applications. Those who teach this sloppy technique twist themselves into knots justifying tricks to approximate flat surfaces using such blades. I have no doubt this is an ancient technique, but I think it is a sad practice that sprung from the carelessness of some craftsmen in flattening their sharpening stones, and with time this bad habit became a tradition in some quarters. I strongly suspect fans of this strange way of doing business habitually sand all visible surfaces anyway so tracks and ridges are not a problem for them. But the fact remains that perfectly flat, track/ridge-free surfaces work best for joinery.

Tradition and “monkey see monkey do” are a useful place to start, but as his skill level increases, the thoughtful and efficient craftsman will eventually seek to confirm the validity of the traditions he has been taught. I urge you to get started early.

Sadly, too many people never notice the strange instruction label pasted to their boot’s sole, nor that smelly stuff sloshing around inside.(ツ)

monkey-see-monkey-do
Mommy monkey teaching baby monkey bad habits. When will they ever learn?

Conclusion

As we come to the end of this post, my advice to you, Gentle Reader, is to learn two bedrock basic skills to perfection. First, learn how to keep your sharpening stones flat; And second, learn how to sharpen your blades to have a straight cutting edge. Everything else will flow naturally from these skills. Your blades deserve it. We will talk more about these subjects in the future.

In this post, we have discussed 12 serious points about plane and chisel blades and how to use and improve them all but a few woodworkers in the West are unaware of, or ignore, but which are common knowledge among professional Japanese woodworkers in advanced trades. While condensed, it is enough information to fill a book, but we are giving it to you for the price of bananas (BYOB, remember?). We hope you picked up on each point, and test those that are new to you.

The next installment in this simian soap opera of sharpening will focus less on monkeyshines, and more on stones and techniques. Please stay tuned.

YMHOS

I can’t wait to read the next post!!

Links to Other Posts in the “Sharpening” Series

Sharpening Japanese Woodworking Tools Part 1

Sharpening Part 2 – The Journey

Sharpening Part 3 – Philosophy

Sharpening Part 4 – ‘Nando and the Sword Sharpener

Sharpening Part 5 – The Sharp Edge

Sharpening Part 6 – The Mystery of Steel

Sharpening Part 7 – The Alchemy of Hard Steel 鋼

Sharpening Part 8 – Soft Iron 地金

Sharpening Part 9 – Hard Steel & Soft Iron 鍛接

Sharpening Part 10 – The Ura 浦

Sharpening Part 11 – Supernatural Bevel Angles

Sharpening Part 12 – Skewampus Blades, Curved Cutting Edges, and Monkeyshines

Sharpening Part 13 – Nitty Gritty

Sharpening Part 14 – Natural Sharpening Stones

Sharpening Part 15 – The Most Important Stone

Sharpening Part 16 – Pixie Dust

Sharpening Part 17 – Gear

Sharpening Part 18 – The Nagura Stone

Sharpening Part 19 – Maintaining Sharpening Stones

Sharpening Part 20 – Flattening and Polishing the Ura

Sharpening Part 21 – The Bulging Bevel

Sharpening Part 22 – The Double-bevel Blues

Sharpening Part 23 – Stance & Grip

Sharpening Part 24 – Sharpening Direction

Sharpening Part 25 – Short Strokes

Sharpening Part 26 – The Taming of the Skew

Sharpening Part 27 – The Entire Face

If you have questions or would like to learn more about our tools, please use the questions form located immediately below. Please share your insights and comments with everyone in the form located further below labeled “Leave a Reply.” We aren’t evil Google or incompetent facebook and so won’t sell, share, or profitably “misplace” your information.